Handbook:Alpha/Networking/Introduction/cs

From Gentoo Wiki
Jump to:navigation Jump to:search
This page is a translated version of the page Handbook:Alpha/Networking/Introduction and the translation is 50% complete.
Alpha Handbook
Instalace
O instalaci
Výběr média
Konfigurace sítě
Příprava disků
Instalace stage3
Instalace základního systému
Konfigurace jádra
Konfigurace systému
Instalace nástrojů
Konfigurace zavaděče
Dokončení
Práce s Gentoo
Úvod do Portage
Přepínače USE
Funkce portage
Systém initskriptů
Proměnné prostředí
Práce s Portage
Soubory a adresáře
Proměnné
Mísení softwarových větví
Doplňkové nástroje
Vlastní strom Portage
Pokročilé funkce
Konfigurace sítě
Začínáme
Pokročilá konfigurace
Modulární síťování
Bezdrátové sítě
Přidání funkcí
Dynamická správa

The following networking portion of the handbook describes 'advanced' network configuration for systems running the OpenRC init system utilizing netifrc as the network management system.

For systems running systemd, readers should review see the networking portion of the systemd article.

Getting started

This networking guide presumes that the user has correctly configured the system and has determined the hardware's network interface name(s). The network interface name is produced based on the bus location of the network card(s) in the system. Because of this there is potential for interface name variants including: eno0, ens1, wlan0, enp1s0, etc. Each system may have a slightly different interface name. The following content presumes the name of the interface to configured is eth0, although any of the aforementioned names will work.

To get started configuring the network card, tell the Gentoo RC system about it. This is done by creating a symbolic link from net.lo to net.eth0 (or whatever the network interface name is on the system) in /etc/init.d.

root #cd /etc/init.d
root #ln -s net.lo net.eth0

Gentoo's RC system now knows about that interface. It also needs to know how to configure the new interface. All the network interfaces are configured in /etc/conf.d/net file. Below is a sample configuration for DHCP and static addresses.

FILE /etc/conf.d/netExample network configuration
# For DHCP
config_eth0="dhcp"
  
# For static IP using CIDR notation
config_eth0="192.168.0.7/24"
routes_eth0="default via 192.168.0.1"
dns_servers_eth0="192.168.0.1 8.8.8.8"
  
# For static IP using netmask notation
config_eth0="192.168.0.7 netmask 255.255.255.0"
routes_eth0="default via 192.168.0.1"
dns_servers_eth0="192.168.0.1 8.8.8.8"
Poznámka
If no configuration is mentioned for an interface then DHCP is assumed.
Poznámka
CIDR stands for Classless InterDomain Routing. Originally, IPv4 addresses were classified as A, B, or C. The early classification system did not envision the massive popularity of the Internet, and is in danger of running out of new unique addresses. CIDR is an addressing scheme that allows one IP address to designate many IP addresses. A CIDR IP address looks like a normal IP address except that it ends with a slash followed by a number; for example, 192.168.0.0/16. CIDR is described in RFC 1519.

Now that the interface is configured, we can start and stop it using the following commands:

root #rc-service net.eth0 start
root #rc-service net.eth0 stop
Důležité
When troubleshooting networking, take a look at /var/log/rc.log. Unless the rc_logger variable is set to NO in /etc/rc.conf, information on the boot activity will be stored in that log file.

Now that the network interface has been successfully stopped and started, the next step is to have it started when Gentoo boots. Here is how to do this.:

root #rc-update add net.eth0 default
root #rc
Poznámka
The last rc command instructs Gentoo to start any scripts in the current runlevel that have not yet been started.