Bluetooth headset
This article describes the configuration of Bluetooth headsets within Gentoo Linux.
Prerequisites
The configurations for Bluetooth and ALSA must have been previously completed (just configurations, some devices do not connect without media-sound/pulseaudio-modules-bt or media-sound/bluez-alsa setup).
Also, ofono-headset USE flags might be useful:
/etc/portage/package.use/pulseaudiomedia-sound/pulseaudio ofono-headset
media-sound/pulseaudio-daemon ofono-headset
Additionally, if you have CONFIG_BT_RFCOMM set as builtin in the kernel, it is possible that the microphone (if there is one) of the headset will not be found by PipeWire/PulseAudio/ALSA.
In this situation, setting CONFIG_BT_RFCOMM as module should be enough for it to be detected.
Configuration
PulseAudio
Following instructions from PulseAudio and BlueZ 5 should be sufficient to make Bluetooth headsets work (through pavucontrol for instance).
There is two protocols for handling microphone input (and button input) from headsets: HSP and HFP. In order for the microphone to work the headset has to switch from the A2DP protocol to HSP/HFP. Headset using HSP will usually work out-of-the-box with the current pulseaudio version.
pulseaudio 13.0 does not support HFP properly. There is ongoing work on this. You might have luck building the current development version from source using this merge request 288 and the accompanying hsphfpd.
ALSA + Bluez 5
You can use bluez-alsa to provide integration between Bluez and ALSA. This setup can be used either completely without Pulseaudio, or you can then use your headset as another ALSA device in Pulseaudio (in which case disable its bluetooth support, so the two don't collide).
Install bluez-alsa:
root #emerge --ask media-sound/bluez-alsain /etc/dbus-1/system.d/bluealsa.conf add lines that allow "sink" and "source" destinations as a part after "org.bluealsa" dbus address.
/etc/dbus-1/system.d/bluealsa.conf<policy user="root">
<allow own_prefix="org.bluealsa"/>
<allow send_destination="org.bluealsa"/>
<allow send_destination="org.bluealsa.sink" />
<allow send_destination="org.bluealsa.source" />
</policy>
<policy group="audio">
<allow send_destination="org.bluealsa"/>
<allow send_destination="org.bluealsa.sink" />
<allow send_destination="org.bluealsa.source" />
</policy>
Run bluez-alsa under root:
root #bluealsa -p a2dp-sink -p a2dp-source --initial-volume=20 &
In your ALSA configuration, /etc/asound.conf (system-wide) or ~/.asoundrc (user-level), specify the parameters of the Bluetooth connection (replace the MAC address with the MAC address of your device):
/etc/asound.conf or ~/.asoundrc# Bluetooth headset
defaults.bluealsa {
interface "hci0" # host Bluetooth adapter
device "10:4F:A8:00:11:22" # Bluetooth headset MAC address
profile "a2dp"
}
A static ALSA configuration is also possible, make sure to change the device name in the below examples for aplay.
/etc/asound.conf or ~/.asoundrc# Bluetooth headset
pcm.!default {
type plug
slave.pcm {
type bluealsa
device "10:4F:A8:00:11:22"
profile "a2dp"
}
hint {
show on
description "Your description of Bluetooth Headset"
}
}
ctl.!default {
type bluealsa
device "10:4F:A8:00:11:22"
}
Make sure the bluetooth and bluealsa services are started. You probably want to add them to your default runlevel via rc-config. Make sure the device is paired and connected to your computer (see Bluetooth for details) and test with aplay, passing the PCM device bluealsa:
user $aplay -D bluealsa some_file.wavFor other applications, the precise option to set the output device may differ.
Changes to ALSA configuration files /etc/asound.conf and ~/.asoundrc are picked up automatically at application start, you don't need to restart the alsasound service.
Hardware volume control:
user $alsamixer -D bluealsaTesting
Play a sound file with mplayer:
user $mplayer -ao alsa:device=bluealsa filenameOr with mpv:
user $mpv --audio-device=alsa/bluealsa filenameIf it works, please add your device to the table of working devices.
Working devices
The capabilities of the device are dependent on the Bluetooth controller being used.
| Device | Headphone | Microphone | BlueZ Version | Notes | |
|---|---|---|---|---|---|
| AfterShokz TREKZ Titanium | Yes | Not tested | 5.50-r2 | ||
| AKG N700NC | Yes | Not tested | 5.52 | Update headset firmware to latest version 0.2.7. | |
| Beats By Dre PowerBeats3 | Yes | Not tested | 5.55 | Apply module loading to /etc/pulse/default.pa and system.pa with latest version of Bluez as device and module will not load otherwise. Supports a2dp. Media key presses work for volume, double press next, single press pause, triple click previous. | |
| Bose SoundSport Free (423729) | Yes | Not tested | 5.55 | ||
| Bose SoundSport Free (774373-0010) | Yes | Not tested | 5.48-r1 | ||
| Bose QC Earbuds | Yes | Not tested | 5.55 | ||
| Bose QC35 II Headset | Yes | Yes | 5.61 | ||
| the BTunes 3 | Yes | Not tested | 5.54 | ||
| Cellular Innovations HFBLU-ST6 | Yes | No | ? | ||
| Comexion M100 | Yes | Yes | 5.64 | Pulseaudio needed native-headset USE flag. Manual switching between A2DP and HFP bluetooth profiles is done with pavucontrol. | |
| Creative BT-W2 USB Bluetooth Dongle | Yes | Not tested | 5.52 | Tested on desktop PC without built-in Bluetooth. Very straightforward setup. Requires kernel USB audio enabled. Volume and Play/Pause work. Pair with any Bluetooth headphones. Compile alsa-plugins with speex libsamplerate and ffmpeg USE flags to provide options for better sampling. | |
| Dell BH200 | Yes | Not tested | ? | ||
| Google Pixel Buds | Yes | Yes | 5.49-r1 | ||
| Huawei FreeBuds | Yes | Not tested | 5.49-r1 | ||
| Jabra MOVE v2.3.0 | Yes | Yes | 5.39 | If supported, AAC codec is selected, otherwise SBC | |
| Jabra Elite 65t | Yes | Yes | 5.70-r1 | ||
| Jabra Elite 2 | Yes | Yes | 5.70-r1 | Sometimes the audio is lost for a very short time. | |
| Jabra Evolve2 75 | Yes | Yes | 5.66-r1 | I needed to install *both* pulseaudio-daemon and pulseaudio with appropriate USE flags (sys-apps/portage-3.0.44-r1 dated Sat Apr 1 2023. Feel free to remove this instruction if the dependency is no longer present.) | |
| JBL CLUB PRO+ TWS | Yes | Not tested | 5.66-r1 | ||
| JBL E40BT | Yes | Not tested | 5.47 | ||
| JBL JBL Endurance SPRINT | Yes | Not tested | 5.55 | ||
| JBL GO+ | Yes | Not tested | 5.50-r2 | ||
| JBL Live 400BT | Yes | Yes | 5.62-r3 | It seems some them come with factory defect making mic level too low and impossible to change | |
| JBL T450BT | Yes | Not tested | 5.43 | ||
| JBL Live 500BT | Yes | No | 5.54 | ||
| JBL Live 770NC | Yes | Yes | 5.71-r1 | The kernel option CONFIG_BT_RFCOMM need to be set as module. This was tested with media-video/pipewire 1.0.1 (via media-video/wireplumber 0.5.17-r1). | |
| JBL FLIP5 | Yes | No | 5.70-r1 | ||
| LG HBS730 | Yes | No | ? | ||
| Lenovo HX106 | Yes | Yes | 5.61 | media-sound/bluez-alsa-3.1.0 is necessary | |
| Marshall Major II | Yes | Not tested | 5.51 | ||
| Marshall MID | Yes | Not tested | 5.51 | ||
| Marshall Stockwell | Yes | Not tested | BlueZ 5.54 | Bluetooth Speaker tested successfully. Microphone not applicable | |
| Mi Bluetooth Headset Basic LYEJ02LM | Yes | Yes | BlueZ 5.61-r1 | Bluetooth Headset Speaker and Microphone both tested successfully. | |
| Nokia BH-214 | Yes | No | 4.101 & 5.39 | ||
| Nokia BH-604 | Yes | Yes | ? | ||
| Parrot Zik | Yes | Not tested | ? | ||
| Philips SBH6201 | Yes | Yes | ? | ||
| Philips SBH9100 | Yes | Not tested | ? | ||
| Pioneer SE-MS9BN-G | Yes | Yes | 5.50-r1 | Microphone tested successfully with BlueZ 5.50-r1 and HSP/HFP profile. Volume and play-pause buttons recognized as Multimedia events in Xfce (XF86AudioNext - XF86AudioPrev - XF86AudioPlay). No special bluetooth configuration is required. You should only make sure that pulseaudio is built with native-headset useflag, and that pulseaudio spawns correctly from your X session. | |
| Plantronics BackBeat GO | Yes | Not tested | ? | ||
| Plantronics BackBeat PRO 2 | Yes | Yes | 5.52 | The microphone works with HSP/HFP. Pulseaudio have to be built with native-headset USE flag to have the microphone working. Buttons work when "User level driver support" is added in the kernel. | |
| Prestigio PBHS1 | Yes | Not tested | ? | ||
| Sennheiser HD 4.40 BT | Yes | Not tested | 5.50-r2 | ||
| Sennheiser MM 550-X Travel | Yes | Yes | 5.27 | Microphone tested successfully with BlueZ 4.x/HSF. With bluez 5.58-r1 switch of audio profile from A2DP to HSP/HFP does not work. Hence microphone does not work. | |
| Sennheiser PXC 550 | Yes | Not tested | 5.50-r1 | Confirmed working with older versions, but not sure how far back. Tested with bluez-alsa (currently 1.3.1), not Pulse Audio. Media controls not tested. | |
| Sennheiser URBANITE XL Wireless | Yes | Not tested | 5.46 | Volume swipes are working | |
| Shure Aionic TW2 | Yes | Not tested | 5.64 | May need to re-pair after pairing with another device. | |
| Shure RMCE-BT2 | Yes | Not tested | 5.52 | Volume buttons adjust volume locally, not on host device. Microphone not detected. Tested with Pulseaudio, not with bluez-alsa. | |
| Shure True Wireless Secure Fit Adapter 2 | Yes | Not tested | 5.52 | No issues. | |
| Sony DR-BTN200 | Yes | No | 5.39 | All buttons except "Call" work and can be assigned shortcuts in the DE | |
| Sony MDR-1000X | Yes | No | 5.50-r3 | Volume swipes are working, prev/next swipes don't work. | |
| Sony MDR-ZX750BN | Yes | No | ? | The change track and volume buttons work. | |
| Sony MDR-ZX770BT | Yes | Not tested | 4.101 & 5.25 | 4.101 requires Enable=Socket in /etc/bluetooth/audio.conf | |
| Sony SBH20 | Yes | Not tested | ? | ||
| Sony SBH52 | Yes | Yes | ? | The buttons work and can be assigned actions in KDE. Supported rate 4800. | |
| Sony WH-XB900N | Yes | Yes | 5.62-r3 | Everything works well at least with pipewire. Make sure kernel's RFCOMM/BNEP are compiled as modules and upower is compiled with "ios" use flag | |
| Sony WH-CH700N | Yes | Not tested | 5.50-r3 | Volume control works. BlueZ 5: blue-alsa | |
| Sony WH-CH710N | Yes | Yes | 5.62-r3 | Tested with pipewire-0.3.36. A2DP bt profile for good audio quality only, HSP/HFP bt profile for having both mic and audio. | |
| Sony WH-1000XM2 | Yes | Yes | 5.56-r1 | The touch interface (volume) on the right speaker works. | |
| Sony WH-1000XM3 | Yes | Yes | 5.55:0/3 | The touch interface on the right speaker works. Strange echo of external sounds in headset mode (possibly feature not error). With bluez 5.58-r1 switch of audio profile from A2DP to HSP/HFP does not work. Hence microphone does not work. | |
| Sony WH-1000XM4 | Yes | No | 5.66-r1 | Haven't been able to get the microphone to work yet. | |
| Sony WH-1000XM5 | Yes | Yes | 5.68 | Touch panel is fine. Maybe you need to configure touch controls by hand in KDE for some app like Audacious. Auto-switch A2DP/HSP profile when activate mic, LDAC and mSBC supported. Pair with Intel AX201 USB adapter. | |
| Sony WI-1000X | Yes | Not Tested | 5.62-r3 | ||
| Sony Ericsson HBH-DS200 | Yes | Not tested | 4.101 & 5.43 | BlueZ 4: software volume control via .asoundrc. BlueZ 5: BlueALSA | |
| Sony Ericsson HBH-DS970 | Yes | Not tested | ? | Requires Enable=Socket in /etc/bluetooth/audio.conf. | |
| Soundcore Spirit Bluetooth Headphones | Yes | Not tested | 5.50-r2 | ||
| Teufel MUTE BT | Yes | Yes | 5.47 | ||
| Apple AirPods Pro | Yes | No | 5.54 | Recording looks like it could work in ALSA, when profile is set to "sco". Recording does not work under normal PulseAudio use. | |
| Apple AirPods (1st generation) | Yes | No | 5.54 | Recording is probably same as AirPods Pro. | |
| Xiaomi Redmi AirDots | Yes | No | 5.54 | There might be a way to make the microphone work, if you mess with pulseaudio and manage to get HSP/HFP to work, but I couldn't do it. | |
| CaseGuru CGpods 5.0 | Yes | Not tested | 5.54 | ||
| XO-ET32 | Yes | Not tested | 5.68 | ||
| Soundcore Life Q30 | Yes | Yes | 5.55 | Playback via Pulseaudio worked with A2DP out of the box, attempts to get the microphone work via HSP/HFP were unsuccessful with both native-headset and ofono/phonesim mess. I was able to get it working with bluez-alsa and then added the device to Pulseaudio as described on bluez-alsa wiki. |
Troubleshooting
When you have minimal setup, you may encounter:
user $bluetoothctl[bluetooth]# connect <MAC> Attempting to connect to <MAC> Failed to connect: org.bluez.Error.Failed br-connection-profile-unavailable
This is due to PulseAudio not running [1], so start some audio playback first to trigger PA server startup and then try again to connect with BT headset.
Can't open input device
Compile and load the uinput kernel module, when things don't work, and the logs show this error:
bluetoothd: Can't open input device: No such file or directory (2)
bluetoothd: AVRCP: failed to init uinput for 00:16:44:FD:6B:A0
bluetoothd: Unable to select SEP
Device Drivers --->
Input device support --->
[*] Miscellaneous devices --->
<M> User level driver support
No audio service is available
After updating to net-wireless/bluez-5.xx it might happen, that a Bluetooth headset is connected, but ALSA/PulseAudio fails to pick up the connected device.
An error message like this might be shown in the output of PulseAudio:
I: [pulseaudio] module-card-restore.c: Restoring profile for card bluez_card.00_16_94_0B_6F_DE.
I: [pulseaudio] card.c: Created 10 "bluez_card.00_16_94_0B_6F_DE"
bt_audio_service_open: connect() failed: Connection refused (111)
W: [pulseaudio] module-bluetooth-device.c: Bluetooth audio service not available
W: [pulseaudio] module-bluetooth-device.c: Service not connected
I: [pulseaudio] card.c: Freed 10 "bluez_card.00_16_94_0B_6F_DE"
E: [pulseaudio] module.c: Failed to load module "module-bluetooth-device" (argument: "address="00:16:94:0B:6F:DE" path="/org/bluez/31716/hci0/dev_00_16_94_0B_6F_DE""): initialization failed.
To fix this, the following needs to be done:
- Enable the audio socket of bluetoothd:
/etc/bluetooth/audio.conf[General]
Enable=Socket
- Restart bluetoothd by doing one of the following things:
- Turn the software wireless kill switch off and on again
root #rfkill block bluetoothroot #rfkill unblock bluetooth- Turn the hardware wireless kill switch off and on again
- Reboot the computer
- Reconnect the Bluetooth headset
Audio device not visible when using GDM
If you are using GDM, but not logging into GNOME (e.g. i3 instead), GDM might block your headset, which will it not being available for PulseAudio. This will result in your headset being connected, but the applications won't see it.
As a workaround, you can switch to a different display manager (e.g. LXDM), or disable PulseAudio for GDM[1]:
/var/lib/gdm/.config/pulse/client.confautospawn = no
daemon-binary = /bin/true
If you have created the file, make sure that GDM can read it:
root #chown gdm:gdm /var/lib/gdm/.config/pulse/client.confAudio device not visible using PulseAudio volume control (but working with ALSA)
According to this forum post, add the following to /etc/pulse/default.pa (and possibly /etc/pulse/system.pa):
/etc/pulse/default.pa### Automatically load driver modules for Bluetooth hardware
.ifexists module-bluez5-device.so
load-module module-bluez5-device
.endif
.ifexists module-bluez5-discover.so
load-module module-bluez5-discover
.endif
Ensure that the pulseaudio and bluetooth USE flags are enabled
See also
External resources
References
- ↑ Stanislav Naumuk. Bluetooth a2dp, Debian Wiki, June 13th, 2015. Retrieved on March 18th, 2019.